文章摘要
Tri-Arc与Tandem双丝电弧焊的工作原理对比分析
Comparative Analysis on Principle of Tri-Arc and Tandem Dual Wire Arc Welding
Received:May 11, 2020  Revised:July 10, 2020
DOI:10.3969/j.issn.1674-6457.2020.04.012
中文关键词: Tri-Arc双丝焊  Tandem双丝焊  高焊丝熔敷率  低焊接热输入
英文关键词: Tri-Arc dual wire welding  Tandem dual wire welding  high wiredeposition rate  low welding heat input
基金项目:深圳市科技计划(JSGG20180504165617788)
Author NameAffiliation
GENG Zheng 1. State Key Laboratory of Advanced Welding & Joining, Harbin Institute of Technology, Harbin 150001, China 
LI Shao-nong 2. Shenzhen Riland Industrial Co., Ltd., Shenzhen 518001, China 
WEI Zhan-jing 2. Shenzhen Riland Industrial Co., Ltd., Shenzhen 518001, China 
WANG Wei 2. Shenzhen Riland Industrial Co., Ltd., Shenzhen 518001, China 
QIU Guang 2. Shenzhen Riland Industrial Co., Ltd., Shenzhen 518001, China 
Hits: 3765
Download times: 2423
中文摘要:
      目的 介绍一种称为Tri-Arc的新型双丝电弧焊接方法。方法 将Tri-Arc双丝电弧焊与应用较广的Tandem双丝电弧焊的系统构成和焊接电流波形进行对比分析。结果 Tri-Arc和Tandem两种双丝电弧焊接方法所使用的双丝焊枪相近,双电源相位同步控制和U/I脉冲控制方式类似。Tri-Arc和Tandem两种双丝电弧焊接方法的差异在于:Tandem双丝电弧焊的2个电弧是相对独立的,而Tri-Arc双丝电弧焊的2个电弧是相互耦合的,因此Tri-Arc双丝电弧焊又具有旁路耦合电弧的某些特点。结论 这种新型的Tri-Arc双丝电弧焊不仅具有与Tandem双丝电弧焊一样的高焊丝熔敷率,而且具有比Tandem双丝电弧焊更低的焊接热输入。
英文摘要:
      The paper aims to introduce a novel dual wire arc welding method called Tri-Arc. By comparison and analysis of the system composition and welding current waveform between the Tri-Arc dual wire arc welding and the widely used Tandem dual wire arc welding, it was found that the commonness of the two double wire welding methods was using similar dual wire welding torch, similar double power phase synchronous control and U/I pulse control mode, etc. The difference between the two dual wire arc welding methods was that the two arcs of the Tandem dual wire arc welding were relatively independent, while the two arcs of the Tri-Arc dual wire arc welding were coupled with each other. As a result Tri-Arc dual-wire arc welding had some characteristics of bypass coupling arc. The results show that this new Tri-Arc dual wire arc welding not only has the same high wire deposition rate as Tandem dual wire arc welding, but also has lower welding heat input than Tandem dual wire arc welding.
View Full Text   View/Add Comment  Download reader
Close

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

You are the789387visitor    渝ICP备15012534号-4

>Copyright:Journal of Netshape Forming Engineering 2014 All Rights Reserved

>Postal Code: Phone:Fax: Email:

>    

渝公网安备 50010702501719号