文章摘要
许明三,陈相档,王建国,等.40Cr轴面激光熔覆Ni60数值模拟[J].精密成形工程,2022,14(5):134-142.
XU Ming-san,CHEN Xiang-dang,WANG Jian-guo,et al.Numerical Simulation of Laser Cladding Ni60 on 40Cr Shaft Surface[J].Journal of Netshape Forming Engineering,2022,14(5):134-142.
40Cr轴面激光熔覆Ni60数值模拟
Numerical Simulation of Laser Cladding Ni60 on 40Cr Shaft Surface
  
DOI:10.3969/j.issn.1674-6457.2022.05.019
中文关键词: 轴面  激光熔覆  Ni60  温度场  流场
英文关键词: shaft surface  laser cladding  Ni60  temperature field  flow field
基金项目:国家自然科学基金(51575110);福建省自然科学基金(2020J01872)
作者单位
许明三 福建工程学院 机械与汽车工程学院福州 350118
福建工程学院 先进制造生产力促进中心福州 350118 
陈相档 福建工程学院 机械与汽车工程学院福州 350118
福建工程学院 先进制造生产力促进中心福州 350118 
王建国 福建工程学院 机械与汽车工程学院福州 350118
福建工程学院 先进制造生产力促进中心福州 350118 
叶建华 福建工程学院 机械与汽车工程学院福州 350118
福建工程学院 先进制造生产力促进中心福州 350118 
韦铁平 福建工程学院 机械与汽车工程学院福州 350118
福建工程学院 先进制造生产力促进中心福州 350118 
摘要点击次数: 1939
全文下载次数: 747
中文摘要:
      目的 针对激光熔覆过程中熔池内部复杂的传热和对流现象,分析激光功率和扫描速度对熔池内部温度场、流场演变和分布的影响。方法 采用双椭球热源模型,建立了40Cr轴面基体激光熔覆Ni60粉末过程的三维温度场流场数值模型,并进行试验验证。结果 熔覆过程形成了近似椭球体的熔池,最高温度位于移动光斑中心偏后方,达到了2 080.4 K;熔池内部金属流体形成了2个方向相反的旋流,熔池表面边缘受马兰戈尼对流的影响流速最大,达到了0.49 m/s。通过对比试验和模拟获得了熔覆层截面最高温度,最高温度最大相对误差为10.1%,数值模型具有较高的准确性。结论 扫描速度对熔池存在时间和形状的影响要大于激光功率,激光功率对流场的影响大于扫描速度。研究结果为轴面激光熔覆成形提供相关理论依据。
英文摘要:
      There is complex heat transfer and convection phenomena in the molten pool during laser cladding. The effects of laser power and scanning speed on the evolution and distribution of temperature field and flow field in the molten pool were analyzed. The double ellipsoid heat source model was used to establish the three-dimensional temperature field and flow field numerical model of laser cladding Ni60 powder on 40Cr shaft substrate, and the experimental verification was carried out. The results showed that an approximate ellipsoidal pool was formed during cladding. The maximum temperature is located behind the center of the moving spot, reaching 2 080.4 K. The metal fluid in the molten pool formed two swirls in opposite directions, and the flow velocity at the surface edge of the molten pool was the largest under the influence of Marangoni flow, reaching 0.49 m/s. By comparing the maximum temperature of the cladding cross section obtained by the experiment and simulation, the maximum relative error of the maximum temperature was 10.1%, and the numerical simulation model had good accuracy. The effect of scanning speed on the time and shape of molten pool was greater than laser power, and the influence of laser power on the flow field was greater than that of scanning velocity. The results can provide theory for laser cladding on shaft surface.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第14770953位访问者    渝ICP备15012534号-4

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

    

渝公网安备 50010702501719号