文章摘要
刘杰慧,鲜勇,刘政,等.Fe和C元素对铜合金组织结构及力学性能的影响[J].精密成形工程,2021,13(5):141-146.
LIU Jie-hui,XIAN Yong,LIU Zheng,et al.Effects of Fe and C on the Structure and Mechanical Properties of Copper Alloys[J].Journal of Netshape Forming Engineering,2021,13(5):141-146.
Fe和C元素对铜合金组织结构及力学性能的影响
Effects of Fe and C on the Structure and Mechanical Properties of Copper Alloys
投稿时间:2021-06-21  
DOI:10.3969/j.issn.1674-6457.2021.05.018
中文关键词: 热压烧结  Cu-Fe-C合金  微观组织  力学性能
英文关键词: hot press sintering  Cu-Fe-C alloy  microstructure  mechanical properties
基金项目:四川省科技厅项目(2018JY0278)
作者单位
刘杰慧 成都工业学院 材料与环境工程学院成都 611730 
鲜勇 成都工业学院 材料与环境工程学院成都 611730 
刘政 成都工业学院 大学科技园成都 611730 
杨超 成都工业学院 材料与环境工程学院成都 611730 
丁义超 成都工业学院 材料与环境工程学院成都 611730 
肖杰 成都工业学院 材料与环境工程学院成都 611730 
摘要点击次数: 2533
全文下载次数: 1699
中文摘要:
      目的 增强铜合金的强度、硬度,拓展该合金的应用范围。方法 在铜粉中添加不同比例共析成分的铁粉和石墨粉,利用真空热压烧结法,制备Cu-Fe-C合金。结果 热压烧结可以原位生成渗碳体;随着铁粉、石墨粉添加量的增加,铜基体的硬度持续增加,Cu-Fe-C合金的抗拉强度先上升后下降;当铁粉和石墨粉的质量分数为5%时,抗拉强度由197 MPa增大至281 MPa,提升了43%。结论 强度和硬度的升高是第二相引起的晶粒细化和第二相强化所致,强度先升后降的原因是随着石墨粉的增加,石墨粉聚集区逐渐增多,割裂了铜基体。
英文摘要:
      This paper aims to enhance the strong hardness of the copper alloy and expand the application range of the alloy. Cu-Fe-C alloy was prepared by adding iron powder and graphite powder with different proportions of eutectoid composition to copper powder, and using vacuum hot pressing sintering method. The effect of the addition of iron powder and graphite powder on the microstructure and mechanical properties of Cu-Fe-C alloy was studied. The results show that hot press sintering can generate cementite in situ; with the increase of iron powder and graphite powder addition, the hardness of the copper matrix continues to increase, but the tensile strength of Cu-Fe-C alloy first increases and then decreases; when the powder and graphite powder are added at 5% (mass fraction, the same below), the tensile strength increases from 197 MPa to 281 MPa, an increase of 43%. The increase of the strong hardness is caused by the second phase to refine the crystal refinement and the second phase strengthening, and the reason for the first increase and then decrease of the strength is that with the increase of graphite powder, the graphite powder accumulation area gradually increases, which splits the copper matrix.
查看全文   查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第14782931位访问者    渝ICP备15012534号-4

>版权所有:《精密成形工程》编辑部 2014 All Rights Reserved

>邮编:400039 电话:023-68679125传真:02368792396 Email: jmcxgc@163.com

    

渝公网安备 50010702501719号