韩飞,陈刚,刘洪伟,等.铸态ZK60 镁合金往复挤压的组织与性能[J].精密成形工程,2017,9(2):40-44.
HAN Fei,CHEN Gang,LIU Hong-wei,et al.Microstructure and Properties of Cyclic Extrusion and Compression Using As-cast ZK60 Magnesium Alloy[J].Journal of Netshape Forming Engineering,2017,9(2):40-44. |
| 铸态ZK60 镁合金往复挤压的组织与性能 |
| Microstructure and Properties of Cyclic Extrusion and Compression Using As-cast ZK60 Magnesium Alloy |
| 投稿时间：2017-02-28 修订日期：2017-03-10 |
| DOI：10.3969/j.issn.1674-6457.2017.02.007 |
| 中文关键词: 往复挤压 ZK60 镁合金 微观组织 力学性能 |
| 英文关键词: cyclic extrusion and compression ZK60 magnesium alloy microstructure mechanical property |
| 基金项目: |
|
| 摘要点击次数: 4961 |
| 全文下载次数: 3781 |
| 中文摘要: |
| 目的 探索工艺参数对微观组织和力学性能的影响。方法 材料选用铸态ZK60 合金，通过试验研究挤压比、往复挤压道次对镁合金微观组织演变的影响，分析挤压比对T6 处理的材料力学性能的影响。结果 在一定范围内增大挤压比和增加往复挤压道次均有助于组织细化。在350 ℃、挤压比为8 时，经过8 道次往复挤压变形可以细化晶粒到3 μm 左右。晶粒尺寸达到5 μm 以下，增加往复道次使晶粒细化的效果不明显，但有利于晶粒的均匀化。在往复挤压温度350 ℃，挤压比8，往复道次8 的条件下，经过T6 处理的试样具有良好的综合力学性能，伸长率达到22.1%，抗拉强度为308.6 MPa。结论 ZK60 镁合金在往复挤压和动态再结晶过程中，晶粒的细化与往复挤压道次和挤压比有关。若挤压比较小，尽管往复道次较大，但是晶粒细化的效果不明显；合理的匹配挤压比与往复道次，能获得细小、均匀的组织。 |
| 英文摘要: |
| The paper aims to investigate effects of process parameters on microstructure and mechanical properties of as-cast ZK60 alloy. As-cast ZK60 alloy was selected to test and observe influences of cyclic extrusion and compression on microstructure of magnesium alloy and effects of extrusion ratio on mechanical properties of material subjected to T6 treatment. Increasing the extrusion ratio and CEC pass to a certain extend could contribute to the refinement of the microstructure. In CEC process for 8 passes at 350 ℃ with extrusion ratio of 8, the grain could be refined to about 3 μm. The refining effect of grain size was not obvious with the increase of CEC pass when the grain size is below 5 μm, but it was beneficial to the uniformity of grain. The sample processed by CEC for 8 passes at 350 ℃ with extrusion ratio of 8 after T6 treatment had good comprehensive mechanical property. The corresponding elongation reached 22.1% and the tensile strength reached 308.6 MPa. In the process of CEC and dynamic recrystallization, grain refinement of ZK60 magnesium alloy is related to the CEC pass and extrusion ratio. If extrusion ratio is relatively small, even if the CEC pass is large, the effect of grain refinement is not obvious. Reasonable matching extrusion ratio and CEC pass can obtain refined and uniform microstructure. |
|
查看全文
查看/发表评论 下载PDF阅读器 |
| 关闭 |
渝公网安备 50010702501719号